DMO565R DATASHEET PDF

DMOR Datasheet PDF, DMOR datasheet, DMOR pdf, DMOR pinout, DMOR data, circuit, ic, manual, substitute, parts. Description. The FSDMRE, FSDMRE and FSDMRE are an integrated Pulse Width Modulator (PWM) and. SenseFET specifically designed for. Features. • Optimized for Quasi-Resonant Converter (QRC). • Advanced Burst- Mode Operation for under 1W Standby. Power Consumption. • Pulse-by-Pulse.

Author: Faejar Mitaur
Country: Bahamas
Language: English (Spanish)
Genre: Music
Published (Last): 15 April 2009
Pages: 386
PDF File Size: 11.30 Mb
ePub File Size: 7.35 Mb
ISBN: 974-5-85292-446-8
Downloads: 50225
Price: Free* [*Free Regsitration Required]
Uploader: Jujora

Overload is defined as the load current exceeding a pre-set level due to an unexpected event. Because of the pulse-by-pulse current limit capability, the maximum peak current through the Sense FET is limited, and therefore the maximum input power is restricted with a given input voltage. In dmo655r situation, the protection circuit should be activated in order to protect the SMPS.

At this point switching stops and the output voltages start to drop at a rate dependent on standby current load. When the temperature exceeds approximately C, the thermal shutdown is activated.

This event typically happens when the input voltage is increased or dmo55r output load is decreased. This pin is internally connected to the inverting input of the PWM comparator. TempFeedback Source Current vs.

DMOR Datasheet –

Qlt datasheet pdf – datasheet pdf QLT datasheet, This device is an integrated high voltage power switching regulator which combine an avalanche rugged Sense FET with a current mode PWM control block.

Burst mode operation alternately enables and disables switching of the power Sense FET thereby reducing switching loss in Standby mode. Published on Apr View If Vfb exceeds 2. It is ddatasheet to drive the transformer directly. As the load decreases, the feedback voltage decreases. In order to prevent this situation, an over voltage protection OVP circuit is employed.

  DEMONHUNTER CODEX PDF

DMO565R View Datasheet(PDF) – Fairchild Semiconductor

Then, Vfb climbs up in a similar manner to the over load dno565r, forcing the preset maximum current to be supplied to the SMPS until the over load protection is activated. In this generation the startup resistor is replaced by an internal high voltage current source.

These parameters indicate the inductor current. Assuming that the 0. When Vcc reaches the UVLO stop voltage, 8V, the protection is reset and the internal high voltage current source dstasheet the Vcc capacitor via the Vstr pin. The delay time for shutdown is the time required to charge CB from 2. In this manner, the auto-restart can alternately enable and disable the switching of the power Sense FET until the fault condition is eliminated see Figure 6.

Rockchip RK datasheet V0. If the secondary side feedback circuit were to malfunction or a solder defect caused an open in the feedback path, the current through the opto-coupler transistor becomes almost zero. Then, the FSDMRB continues its normal switching operation and the power is supplied from the auxiliary transformer winding unless Vcc goes below the stop voltage of 8V. The collector of an opto-coupler is typically tied to this pin.

Therefore, the peak value of the current through the Sense FET is limited. During start up, the power is supplied by an internal high voltage current source that datasheett connected to the Vstr pin. Excessive voltage across the Rsense resistor would lead to incorrect feedback operation in the current mode PWM control.

  F4A33 REPAIR PDF

This pin is connected directly to the high voltage DC link.

DMOR Datasheet PDF – Fairchild Semiconductor

This device is a basic platform well suited for cost effective designs of flyback converters. When the reference pin voltage of the KA exceeds the internal reference voltage of 2.

Ql5 datasheet pdf -? However, even when the SMPS is in the normal dmoo565r, the over load protection circuit can be activated during the load transition. At startup, the internal high voltage current source supplies internal bias and charges the external capacitor that is connected to the Vcc pin.

When Vcc reaches 12V, the internal high voltage current source is disabled and the power is supplied from the auxiliary transformer winding.

Ql5 datasheet pdf QL5 datasheet, This pin is the positive supply voltage input. Free standing with no heat-sink under natural convection. It also helps to prevent transformer saturation and reduce the stress on the secondary diode during startup.

In order to avoid this undesired operation, the over load protection circuit is dxtasheet to be activated after a specified time to determine whether it is a transient situation or an overload situation.

Author: admin