LEPD Octal Serial Solenoid Driver. EIGHT LOW RDSon DMOS OUTPUTS @ 25°C VCC 5%) 8 BIT SERIAL INPUT DATA (SPI) 8 BIT SERIAL DIAGNOSTIC . LEPD datasheet, LEPD circuit, LEPD data sheet: STMICROELECTRONICS – Octal serial solenoid driver,alldatasheet, datasheet, Datasheet. LEPD datasheet, LEPD circuit, LEPD data sheet: STMICROELECTRONICS – OCTAL SERIAL SOLENOID DRIVER,alldatasheet, datasheet.
|Published (Last):||6 August 2016|
|PDF File Size:||18.26 Mb|
|ePub File Size:||16.84 Mb|
|Price:||Free* [*Free Regsitration Required]|
List of figures List of figures Figure 1. Any differences would point to a fault on p9822epd output. Once the delay period has elapsed, the output voltages are sensed by the comparators and any output with voltages higher than 1. Page 5 L9822eod 1 Block diagram Figure 1. Page 4 List of figures List of figures Figure 1. If the output was programmed ON by clocking in a zero, and a one came back as the di- agnostic bit for that output, the output pin was still high and a short circuit or overload condition exists.
Copy your embed code and put on your site: Elcodis is a trademark of Elcodis Company Ltd. Each channel is independently controlled by an output latch and a common Electrical specifications 3 Electrical specifications 3. If the output was programmed OFF by clocking in a one, and a zero came back as the diagnostic bit for that output, nothing had pulled the output pin high and it must be floating, so an open circuit condition exists for that output.
Page 12 Functional description 4. LE Information in this l9822epv is provided solely in connection with ST products. Revision history 6 Revision history P9822epd 6. Page 2 Contents Contents 1 Block diagram. Each output has a current limit circuit which limits the maximum output current to at least 1.
The diag- nostic bits should be identical to the bits that were first clocked in. Page 13 LE Figure 6. Download datasheet Kb Share this page. I LE Changes characteristics, the max.
At the rising edge of CE the shift register data is latched into the parallel latch and the output stages will be actuated by the new data. Clock in the same control byte Page 7 LE 2. Clock in a new control byte. LE List of tables Table 1. Page 16 Revision history 6 Revision history Table 6.
(PDF) L9822EPD Datasheet download
Page 9 LE Table 5. Wait microseconds or so to allow the outputs to settle. Checking datashet fault conditions may be done in the fol. Clock in the same control byte and observe the diag- nostic data that comes out of the device. PowerSO pin connection top view Figure 3.
This allows the part to overcome any high inrush cur- rents that may flow immediately after turn on. Contents Contents 1 Block diagram.
Data is transmitted serially to the device using the. Clock in a new control byte. The SCLK input is gated by the. Page 11 LE 4. Datasgeet 1 Block diagram Figure 1. All other trademarks are the property of their respective owners.
LEPD datasheet, Pinout ,application circuits OCTAL SERIAL SOLENOID DRIVER
LEPD datasheet and specification datasheet Download datasheet. This allows the part to overcome any high inrush cur. Pin description 2 Pin description Figure 2. Page 8 Electrical specifications 3 Electrical specifications 3. LEPD datasheet and specification datasheet. Page 15 LE Figure 8. Home – IC Supply – Link. Clock in the dataasheet control byte and observe the diag.
L9822EPD PDF Datasheet浏览和下载
Any differences would point to a fault. Page 6 Pin description 2 Pin description Figure 2. Status monitor function is available on all output. Byte Timing with Asynchronous Reset.
Multiwatt 15 datassheet data and package dimensions DIM. Page 3 LE List of tables Table 1.