MP40 Data Sheet, application/pdf, MB, 08/06/ VorTech MP40w ES Propeller Pump Gen 2 MP40 Manual, application/pdf, MB, 10/27/ Your vortech propeller pump before you start, Adjust the pin spacer • Read online or download PDF • EcoTech Marine Gen 2 MP40 User Manual. MP40w ES. MP10 ES/ MP10w ES. For the full VorTech Pump manual, please visit our website at • Read this manual before installing .

Author: Mezile Mezizragore
Country: Belize
Language: English (Spanish)
Genre: Life
Published (Last): 19 April 2010
Pages: 332
PDF File Size: 4.38 Mb
ePub File Size: 9.44 Mb
ISBN: 430-2-24743-226-8
Downloads: 74826
Price: Free* [*Free Regsitration Required]
Uploader: Fecage

Any water allowed into these components can damage them enough to require replacement. Page 34 For this tank we recommend that you place the master pump running an EcoSmart mode on the right end of the back pane of glass, and a slave pump on the left side.

This can result in death of your fish and coral manul.

For this tank we recommend that you place the master pump running an EcoSmart mode on the right end of the back pane of glass, and a slave pump on the left side. In some cases, an entire aquarium can be destroyed. Page of 44 Go.

EcoTech Marine Gen 2 MP40 User Manual

Assigning Local Max Speed To A Slave While normally you cannot change the speed of a slave pump, because the speed is determined entirely by the master pump, with the EcoSmart driver you now have the ability to control the maxi- mum speed of individual slave pumps independently from the master. Protect these components from splashes of any kind. Notes on placement The VorTech creates over 3, gallons per hour of low velocity flow within your aquarium.

  KMA 373 TAHUN 2002 PDF

If it fails again, contact EcoTech Marine Support for further assistance. Page 37 Upgrade Completed Successfully: Got it, continue to print.

Untitled Document

EcoSmart Driver Page 13 – Section 3. It may then be cleaned of any obstructions. By pressing ‘print’ button you will print only current page. Operational Modes At this point, you can press the set button to cycle through the different values that the current set- ting can be saved to. Adjust the pin spacer. The dim LEDs showing the speed setting. Use of this module in products not consented by EcoTech Marine is prohibited. Page 33 – Section ecitech. Page 23 Short Pulse Mode can then be used if you would like a wave running all the time, or you can use an EcoSmart mode which will auto-load your saved wave frequency and use it during points in the EcoSmart program.

Safety Warnings Page 5 Page 6 – Chapter 2: Maintenance Full Driver Memory Clear In order to clear out a saved wave mp4 must perform a full memory clear on the master driver. This example would be the startup sequence for Firmware Revision 1. Configuration Mode Chapter 5: Complain wrong Brand wrong Model non readable.


For more information on operating slave pumps and configuration, see Chapter 5: To set up this mode, you must calibrate your motor using the following sequence of operations: Adjust the pin spacer The Manusl pump is designed to operate with a constant gap between both halves of the device. Specifications and Operating Parameters Flow: Because there are no other panes of glass to place additional pumps, slave pumps should not be run in the turquoise mode at all for an aquarium with this configuration.

Ecotech Marine EcoSmart User Manual

Please feel free to call or email us. Maintenance Page 36 – Section 6. When turned on, the option button can be used simultaneously with either the set or mode buttons to perform certain configurations. LED will change color to reflect which mode the pump is in.

In this mode, your If none of this works, contact EcoTech Marine to speak with a service represenative.

Author: admin