Abstract. On the basis of main provisions of ISO standards, reproducibility and repeatability in determination of measured characteristics of. Buy ISO ACCURACY (TRUENESS AND PRECISION) OF MEASUREMENT METHODS AND RESULTS – PART 6: USE IN PRACTICE OF. INTERNATIONAL STANDARD ISO ISO/TC 69, Applications of statistical methods, Subcommittee SC 6, Measurement methods.
|Published (Last):||7 April 2009|
|PDF File Size:||20.76 Mb|
|ePub File Size:||6.46 Mb|
|Price:||Free* [*Free Regsitration Required]|
As a result the experiment may have to be repeated to yield the expected preci- sion values. However, for practical reasons, the choice of the number of laboratories is usually a compromise between the availability of lso sources and the desire to reduce izo value of 6, to a satisfactory level.
BS ISO 5725-6:1994
The reference material should have a matrix as close as possible to the matrix of the material to be subjected to the standard measurement method, e. The h and k values are shown in figures B. ISO matallic coatints measurement of coating thickness coulometic method by anodic dissolution.
If the repeatability standard deviation, or, of the stan- dard measurement method is known, the estimate s, can be assessed by the following procedure. Use in practice of ios values Status: If the reproducibility of the measurement method isoo poor, then it will not be practical to achieve a high degree of certainty in the estimate of the bias.
Anwendungen in der Praxis. In the latter case, a careful examination of the working conditions of each laboratory shall be carried out before the assessment of the bias of the standard measurement method is undertaken.
Proceed to Checkout Continue Shopping. IAccuracy trueness and precision of measurement methods and results – Part 1: Click to learn more. The uncertainty in the estimate of the laboratory bias depends on the repeatability of the measurement method and on the number of test results obtained.
Take the smart route to manage medical device compliance. Exactitude justesse et fidelite des resultats et methodes de mesure. As the voice of the U. The results of this computation are summarized in table B. In the latter case, consideration should be given to repeating the experiment with verification at all steps that the standard measurement method is properly implemented.
Annex A forms an integral part of this part of IS0 The laboratory means and vari- ances for each of the five test materials are listed in table 8. If the repeatability standard deviation of the standard measurement method has not been previously deter- mined in accordance with IS0s, will be con- sidered to be the best estimate of it.
The trueness of the measurement method can be investigated by comparing the accepted reference value with the level of the results given by the measurement method. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. The purpose of the two-bottle system was to confirm the absence of the between-bottle variation.
Laboratory means and laboratory variances Lab. You may delete a document from your Alert Profile at any time. Relevant International Standards on sample division should be consulted. Analysis of the results showed that the between- bottle variation was indeed insignificant; the sample was considered to be homogeneous.
Here B is the laboratory component of bias, i. Alternative methods for the determi- nation of the precision of a standard measure- ment method. Learn more about the cookies we use and how to change your settings.
Enoval – References
IS0 l should be read in conjunction with all other parts of IS0including this part, because it gives the underlying definitions and general principles. C Derivation of equations Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee.
When gR is larger than T. Utilization of trueness data Refer to clause 7 of IS0 Outliers and stragglers Level Lab.
ISO Accuracy of measurement methods and results-Part 2 Basic method – MBA智库文档
The work of preparing International Standards is 572-6 carried out through IS0 technical committees. In particular, if outlying values are de- tected, all necessary steps shall be taken to investi- gate the reasons why they have been obtained, including re-appraisal of the suitability of the accepted reference value. In this report the following information shall be given: Please download Chrome or Firefox or view our browser tips.
Unless otherwise stated, a is assumed to be 0. isl
If this is not true, the respective equations given in IS0 should be used to calculate s. Already Subscribed to this document.